Diodes AP3585A/B/C Manuel d'utilisateur télécharger pdf (Page 9)

AP3585A/B/C

Document number: DS36819 Rev. 1 - 2

9 of 18

www.diodes.com

January 2014

AP3585A/B/C

Product Line o

Diodes Incorporated

NEW PRODUCT

Functional Descriptions

The AP3585A/B/C is a voltage-mode single phase synchronous buck controller with embedded MOSFET drivers. This part provides complete

protection functions such as over voltage protection, under voltage protection and over current protection. Inductor current information is sensed

by R

DS(ON)

of the low side MOSFET. The over current protection threshold can be simply programmed by a resistor.

Power on Reset and Chip Enable

A power on reset (POR) circuitry continuously monitors the supply voltage at VCC pin. Once the rising POR threshold is exceeded, the

AP3585A/B/C sets itself to active state and is ready to accept chip enable command. The rising POR threshold is typically 4.2V at VCC rising.

The COMP/EN is a multifunctional pin: control loop compensation and chip enable as shown in Figure 1. An Enable Comparator monitors the

COMP/EN pin voltage for chip enable. A signal level transistor is adequate to pull this pin down to ground and shut down AP3585A/B/C. A 120µA

current source charges the external compensation network with 0.45V ceiling when this pin is released. If the voltage at COMP/EN pin exceeds

0.3V, the AP3585A/B/C initiates its soft start cycle.

The 120µA current source keeps charging the COMP pin to its ceiling until the feedback loop boosts the COMP pin higher than 0.45V according to

the feedback signal. The current source is cut off when V

COMP

is higher than 0.45V during normal operation.

0.3V

0.45V

ENABLE

COMP

ERROR

AMPLIFIER

DISABLE

ENABLE

120A

Figure 1. Chip Enable Function

Soft Start

A built-in Soft Start is used to prevent surge current from power supply input V

during turn-on (Referring to the Functional Block Diagram). The

error amplifier is a three-input device. Reference voltage V

REF

or the internal soft start voltage SS whichever is smaller dominates the behavior of

the non-inverting inputs of the error amplifier. SS internally ramps up to 0.8V in 2ms for AP3585A (to 0.6V in 1.5ms for AP3585B and 0.6V in

2.4ms for AP3585C) after the soft start cycle is initiated. The ramp is created digitally, so there will be 100 small discrete steps. Accordingly, the

output voltage will follow the SS signal and ramp up smoothly to its target level.

The SS signal keeps ramping up after it exceeds the internal 0.8V for AP3585A (0.6V for AP3585B/C) reference voltage. However, the internal

0.8V for AP3585A (0.6V for AP3585B/C) reference voltage takes over the behavior of error amplifier after SS > V

REF

. When the SS signal climbs

to its ceiling voltage (4.2V), AP3585A/B/C claims the end of soft start cycle and enables the under voltage protection of the output voltage.

Figure 2 shows a typical start up interval for AP3585A/B/C where the COMP/EN pin has been released from a grounded (system shutdown) state.

The internal 120µA current source starts charge the compensation network after the COMP/EN pin is released from ground at T1. The COMP/EN

exceeds 0.3V and enables the AP3585A/B/C at T2. The COMP/EN continues ramping up the stays at 0.45V before the SS starts ramping at T3.

The output voltage follows the internal SS and ramps up to its final level during T3 and T4. At T4, the reference voltage V

REF

takes over the

behavior of the error amplifier as the internal SS crosses V

REF

. The internal SS keeps ramping up and stays at 4.2V at T5, where AP3585A/B/C

asserts the end of soft start cycle.

10V/Div

OUT

0.5V/Div

COMP 0.5V/D iv

LGATE 10V/Div

1ms/Div

Figure 2. Soft Start Behavior of AP3585A/B/C

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 17 18

Commentaires sur ces manuels

Pas de commentaire

Diodes AP3585A/B/C Manuel d'utilisateur Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Diodes AP3585A/B/C